Wall hung vanity installation instructions

We will check out the step by step wall hung vanity installation guide with the right steps and attention. Step 1 — Arrange the materials.

The materials needs for the wall hung vanity unit can include. Before you commence working on the all unity, make sure that you are not going to alter the plumbing. In that case, you need to call up a registered plumber. Turn off the water supply before you begin working and turn on a tap so that the water pressure is released.

Remove the old wall hung vanity unit from the wall. Remove any of the tapware, and cut off the waste pipe. You can even cap the end of your water piped so that you can turn on the mains water line while you are working. Remove the screws and bolts used for the old unity. The standard wall hung vanity installation height would be around to mm.

However, you can measure up the height depending upon how high to install floating vanity in your case. Decide where exactly you want to install wall hung unity on the wall. Mark the height of new vanity on the wall.

Ensure that the height is levelled. Mark the centre of the unity and make a corresponding marking on the wall. Also locate the screws or mounting points of the unity and copy them onto the wall. Once all the markings have been made, you know for sure where exactly your wall hung vanity unit will go. Raise the unity to the height that you have marked on the wall.

Make sure that you have used blocks of wood or anything solid that can help you keep the unity stable at the height. Relying on human efforts may not be the right way to go with it.

The wood should be placed such that it elevates the mount to the final wall hung vanity installation height. Using the wood blocks helps you mark exact mounting bolt without having to struggle to hold the vanity. These blocks can also be useful in the final installation. Mark the correct holes in the wall with a pencil. Use the right type of pencil so that you will not miss the markings.

It would also be practical to mark the holes with a marker if the pencil marks are not clear. Using an impact gun or cordless drill, create holes in the wall to hold the vanity securely. You an use anchors for providing an additional security. Finally, install the studs and bolts and tighten them up. Using a washer for the lag bolts can add more strength to the joint and can be the prime floating vanity support requirements. Some vanities come with a decorative caps for the studs.

They ae designed to serve as decoration alone and may not be need otherwise. Use wall hung vanity brackets where you need them. That does it. You have learnt how to install bathroom vanity against wall with ease. Remove the wooden blocks at the bottom. Check for the stability of the wall mounted unity and clear up the debris if any created while you were working on it.

Check for the issues with wall hung vanity with floor drainage as well. Then you can add screws if you like. Reply 6 years ago. The main downside would be the need to cut rebates into the back of the vanity so the back could still fit flush. The brackets kind of resemble French cleats - I can't understand why they didn't just provide a rail instead of tiny brackets Nice idea!

Btw, I also just finished similar project, but we used Ikea kitchen cabinets with countertop for vanity. Because they use rail sustem, its more flexible with stud location, no need to cut drywall or wood.

I was able to mount it to 3 studs and added two snaptoggle bolts for a good measure A rail was what I was expecting when I unpacked the box I've never seen a wall-hung vanity before but now I want one. It really addresses the problem of things falling off the vanity and getting stuck between the cabinet and the wall.

Thanks for posting this. I feel like this little nugget is going to save me a lot of head-scratching over the next few months. In fact its already clarified a project I've had percolating for a few weeks now. Clear and well presented too.

Yeah, there was no shortage of head-scratching on my part when the vanity got delivered and I looked at the hanging system.

Good luck with whatever it is you have planned. I love seeing clever solutions like this, glad you shared it. This approach is now mentally logged for future reference :. Thanks Sam. Yeah, the multitool is handy all right. Have already used it more than the reciprocating saw I bought a few years back. Much less violent and good for precision demo work. Introduction: How to Install a Wall-hung Vanity. By makendo Instagram makend0 Follow.

More by the author:. About: Analog maker dabbling in digital manufacture More About makendo ». Did you make this project? Use more putty to install the drain assembly. Test the stopper. Thread the mixing tee to the end of the spout. Connect a supply line to each handle, then curl and thread them to the tee. Tighten each connection with a wrench. Tip: Hand-tighten all the fittings; then, once everything is built, go back and cinch them a quarter turn with a wrench. With a helper, turn the countertop right side up and lower it onto 2x4 scraps resting diagonally across the front corners of the vanity.

Add a bead of siliconized acrylic caulk to the top edge of the vanity. Then remove the spacer from the other end, pressing up against the bottom of the sink as you lower the countertop. Use a tape measure to check that the overhang on both ends is consistent.

Squeeze siliconized acrylic caulk onto the rear of the backsplash, center it over the countertop, and press it against the drywall. Add more caulk where the backsplash meets the wall and where it meets the countertop; smooth the beads with your finger. Push the top hinge in place first, pressing it until it snaps, then the bottom hinge.

Repeat on the remaining doors. Then have a plumber install shutoff valves under the sink and make the final connections for water and the drainpipe. Cookie banner We use cookies and other tracking technologies to improve your browsing experience on our site, show personalized content and targeted ads, analyze site traffic, and understand where our audiences come from. By choosing I Accept , you consent to our use of cookies and other tracking technologies.

By Sal Vaglica. Pinterest Email Pocket Flipboard. Webber Cut a 2x6 brace 70 inches long with a circular saw. Webber Measure from the level line down to locate the water supplies and drain. Webber With a helper, rest the vanity on a 5-gallon bucket topped with enough plywood scraps to raise the cabinet to the level line on the wall.